Real Estate Info

Mold in buildings of an enemy of the good old days. These days mold issues are more relevant for at least three reasons.

a) There is increasing respiratory conditions: asthma, allergies, etc.

 

b) There is more mold due to more condensation. The buildings are now more tight, more tight: no holes, no passive ventilation.

 

c) actions for mold problems are steadily increasing.

Molds are filamentous fungi: no animals, not plants.

 

Mold needs to increase moderately high temperatures, and even the foul air, the darkness, but more importantly, it needs two things:

- Humidity

 

- The organic matter for food (natural or synthetic)

Since we can not get rid of organic matter, we must focus our attention and efforts on controlling moisture. You control the moisture you = Prevent mold and spread.

 

Therefore: the fight against mold in buildings is fighting against excessive moisture.

And how do you fight against humidity?

1) The first battle is against condensation. Factors bearing surface and ignite or interstitial condensation are among other:

1. 1 The production of excess moisture from human activity

 

1. 2 Increased occupancy rates

 

1. 3 Very cold winters

 

1. 4 Insufficient heat

 

1. 5 Existence of thermal bridges

 

1. 6 Lack of natural ventilation and forced

 

1. 7 Subheating for economic reasons A. k. a. energy poverty

Most of these factors are influenced. Please check the “4 pillars of CONDENSATION PREVENTION IN BUILDINGS.

2) Then you need to stop any infiltration of moisture, both liquid and gas.

Check roofs, walls, floors, explores the spaces, etc. So far we have seen how to control or prevent mold in buildings. Now we’ll see how to eliminate or control.

 

Gosh! Despite all preventive measures, the green-black nightmare found a way to make his home there! Chris Strogili

 

I like a lot to say: “Do not panic!” But sorry, I can not! You should!

 

Mold is very nasty and persistent. So what are the options?

 

First return on your preventive action. Are they adequate? Do you need to update?

 

Then you have to clean up the mess. I suggest that you should avoid bleach. I think the bleach ineffective, corrosion, dangerous for your health and many materials.

 

I prefer a specialized products for cleaning mold. Beware, however: there are toxic products out there!

Cleaning Procedure

Mold in large concentrations should first be cleaned. Take precautions: masks, goggles, etc. Apply the cleaner onto the infected area and wait as instructed. Then clean with a sponge and a mild detergent. Repeat if necessary, but only once.

 

The mold is dead! What next?

 

Below you can find some good options proved:

1) Isolation

- Strengthen the existing insulation and add new ones.

 

- Eliminate thermal bridges.

 

- A good solution is to isolate the inside with thin boards from extruded polystyrene. The panels are glued onto the substrate. They can raise the surface temperature well above dew point.

 

Then you use paint or wall coverings. All materials must be resistant to mold.

2) anti-condensation paint

These paints are also designed to increase surface temperatures above dew point. Most of them contain fungicides.

 

The insulation capacity is attributed to the glass beads contained in the formula.

 

A minimum consumption of at least 0.5 / m2 bed is essential for the paint to be effective.

3) Antimicrobial – Antifungal paints

These paints can be used either alone or in combination with insulation products and anti-condensation paints.

 

They contain powerful fungicides. For a time spam of up to 10 years, they will not allow the manifestation of mold. From time to time a layer of paint to refresh the antifungal substrates.

http://maconwaterproofing. blogspot. com


View full post on {source}

Tags: buildings, Control, eliminate, Fight, Homes, Mold, prevention